This standard is issued under the fixed designation D ; the 1 These test methods are under the jurisdiction of ASTM Committee D11 on. ASTM D – Standard Test Method for Coated Fabrics. ASTM D Standard Test Methods for Coated Fabrics.
|Published (Last):||23 March 2014|
|PDF File Size:||1.62 Mb|
|ePub File Size:||11.66 Mb|
|Price:||Free* [*Free Regsitration Required]|
Wicking of Coated Cloth. Wicking of Coated Cloth Small wick sized samples are put into a beaker with a water soluble dye.
ASTM D – 06() Standard Test Methods for Coated Fabrics
G Pneumatic Side Opening Grip. Record the force required to crush or cut the specimen. Create two aetm of five specimens each for warp and filling tack-tear strength. Preparing the Specimens The adhesion of coating to fabric test in ASTM D requires two sets of two specimens each for the longitudinal and transverse direction. Low Temperature Bend Test. This test should be performed at the same time as breaking strength with the same specimens.
Another test using a puncture fixture. The width can also be measured with a ruler or more accurate device. We recommend that you purchase the official ASTM standard to achieve the best results. Rated to 8 kN 1, lbf Clamping force up to 16 kN 3, lbf Maximum specimen thicknesses from 10 mm to 30 mm 0. Next run the test machine so that it separates the coating from the backing with a uniform speed of. Dead Load Qstm Strength is similar to the seam strength test.
The other method, the Tongue Tear Method is more common and requires a universal testing machine. Once the samples are cold enough, the samples are folded in half.
We are confident that we have what you are e751 for. The specimen is then torn by the fall of a pendulum through the force of gravity. Record the force necessary for the sample to slip the seam or rupture the fabric. ASTM D is used d7751 ensure the quality of rubber-coated fabrics including tarpaulins, rainwear, outdoor clothing, and similar products.
Preparing the Specimens Use the same specimens as for breaking strength. Test Procedure First, mount the test specimen in the ring clamp. Adhesion Coating to Fabrics. A weighted roller is used to roll over the folded sample to d75 down on the crease. Aetm coated fabric diaphragm will burst, revealing its hydrostatic resistance.
This will be recorded by the UTM controller. Place the load button on the test specimen with the recessed end down and at least 12 mm from any edge of the specimen. This list explains the grips sstm equipment needed for each of the 20 different tests under ASTM D Vise Grips are the standard solution for this test, however self-tightening wedge or scissor grips may be used as well as long as the grip face sizes are appropriate. ASTM D features multiple mechanical properties tests for coated fabrics such as tarps, outdoor clothing, and rain wear.
D Puncture Resistance This test determines the puncture resistance of the coated fabric.
Testing Procedure Wstm you must place the specimen symmetrically on the base plate of your compression tester or universal testing machine. Preparing the Specimens Five specimens should be cut with the smallest dimension at least The weight is measured on a scale with a smaller piece of the fabric. This test is characterized by a spherical plunger fixture.
This test determines the puncture resistance of the coated fabric. Five specimens from each of the warp and filling directions should be tested. Adhesion Coating to Fabrics The adhesion test is used when the coating is stronger than the adhesive that binds it to the fabric.
ASTM D751 Coated Fabrics Rainwear Test Equipment
ASTM D specifies the low temperature bend test. Tests include breaking strength by Procedure A: This special crush resistance fixture is unique to this test. A weight is placed on top of the glass plates to maintain even pressure. Record the force maximum force as the bursting strength of the specimen.
Adhesion of coating shall be the average of the 5 highest peak loads during the test. There are a few types of grip faces that are available including blank, vulcanized rubber, pyramid, or wave. Five specimens should be cut with the smallest dimension at least The adhesion test is used when the coating is stronger than d71 adhesive that binds it to the fabric.
Accelerated Heat D7511 Oven Method. Blocking Resistance at Elevated Temperatures Blocking resistance is tested by folding a piece of fabric sample a couple of times and then placing it in between two glass plates. Square samples are put into the chamber for conditioning.
Low Temperature Impact Test.