Regulation No 26 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of vehicles with. ECE R26 Regulation (03 Series, ) “The uniform regulations on vehicle chapter and section numbering betw een this standard and the ECE R ECE UNIFORM PROVISIONS CONCERNING THE APPROVAL OF: VEHICLES WITH REGARD TO THEIR EXTERNAL PROJECTIONS Incorporating.
|Published (Last):||10 November 2009|
|PDF File Size:||17.53 Mb|
|ePub File Size:||8.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
UN Regulations are established through “series of amendments”, “supplements”, or “corrigenda” based upon proposals put before the World Forum. Regulations in Force 1.
Expand all Collapse all. The first two digits of the approval number indicate that the approval was granted in accordance with the requirements of Regulation No XY in its original form. To apply the 10daN force a flat-ended ram of not more than 50mm diameter shall be used. In case of test on the spoke, that spoke is to be chosen where the bolt hole is closest. When the vehicle ecce travelling in a straight line, no part of the wheels other than the tyres, situated r62 the horizontal plane passing through their axis of rotation shall project beyond the vertical projection, in a horizontal plane of the external surface or structure.
Translation of “Regulation ECE-R26” in Spanish
Annex 2 — Arrangement of the Approval Marks. If a Party to the Agreement applying this Regulation withdraws an approval it has previously granted, it shall forthwith notify the other Contracting Parties applying this Regulation by means of a communication form conforming to the model in Annex 1 to this Regulation.
The regulation applies solely to “fixed-position flashing light devices whose flashing is obtained by the intermittent supply of electric current to the lamp”. It shall be expressed according to the prescription of one International Tyre and Rim Standards and includes at least: Major changes also often include “transitional provisions” which provide dates from which compliance with the requirements becomes mandatory usually beginning with new approvals and then extending to all new products regardless of when they first received approval.
The rim designation shall include in the following order the rim contour designation, the construction, the nominal rim diameter code, the location of the well and the bead-seat configuration, as in the example 5 J x 14 FH. Car, Component Subject Categories: As from the official date of entry into force of the 03 series of amendments, no Contracting Party applying this Regulation shall refuse to grant approval under this Regulation as amended by the 03 series of amendments.
As from 24 months after the date of entry into force of the 02 series of amendments, Contracting Parties applying this Regulation shall grant ECE approval only if the vehicle type to be approved complies with the requirements of this Regulation as amended by the 02 series of amendments. An approval number shall be assigned to each type of separate technical unit approved.
Certificates and licenses
Vehicles equipped with hydropneumatic, hydraulic or pneumatic suspension or a device for automatic levelling according to load shall be tested with the vehicle in eec most adverse normal running condition specified by the manufacturer. The material used for the wheel fixing components shall be at least equivalent to the vehicle manufacturer’s replacement wheel fixing components.
Tests to be carried out should the maximum permitted wheel load subsequently increase. The administrative department which has granted approval of the vehicle type shall be notified of any modification of the vehicle type. An approval number shall be assigned to each type approved.
The approval mark shall be permanent, visible and clearly legible, when the tyre is fitted on the wheel. The Type Approval Authority shall verify the existence of satisfactory arrangements for ensuring effective control cee the conformity of production before type approval is granted. Permanent elongation of the gauge length after fracture L u — L oexpressed as a percentage of the original length L o. Corrigenda r6 used to correct editorial errors.
UN R26 External Projections. In such a case, the Type Approval Authority shall issue the revised pages of the information folder as necessary, marking each revised page to show clearly the nature of the modification and the date of re-issue.
The distance between two consecutive elements of grilles and gaps shall be determined according to the method described in Paragraph 4 of Annex 3 to this Regulation. UN R95 Lateral Collision Protection Occupant Protection in Lateral Collisions Uniform Provisions Concerning the Approval of Vehicles with regard to the Protection of the Occupants in the Event of a Lateral Collision This regulation applies to the lateral collision behavior of the structure of the passenger compartment of M1 and N1 categories of vehicles where the “R” point of the lowest seat is not more than mm from ground level when the unladen vehicle plus kg i.
Exe provisions concerning the approval of vehicles of category L with regard to specific requirements for the electric power train This regulation submitted as document WP.
The following text extract indicates the scope of the document, but does not represent the actual PDF content. Nevertheless, handles which do not comply with this last condition may be accepted if: Notice of approval, or of extension or refusal or withdrawal of approval or production definitively discontinued, of a type of separate technical unit pursuant to this Regulation shall be communicated to the Parties to the Agreement applying this Regulation by sce of a communication form conforming to the model in Annex 4 to this Regulation.
Need more search options?
Licenses and Certificates
In the case where negative results are recorded during one of these visits, the competent authority shall ensure that all necessary steps are taken to re-establish the conformity of production as rapidly as possible.
The external surface of vehicles shall not exhibit, directed outwards, any pointed or sharp parts or any projections of such shape, dimensions, direction or hardness as to be likely to increase the risk or seriousness of bodily injury to a person hit by the external surface or brushing against it fce the event of a collision.
A vehicle representative of the type of vehicle to be approved shall be submitted ee the technical service responsible for conducting the approval tests. UN R25 Head Restraints.
Where original gauge length L o: