CD4066 DATASHEET PDF

The CDBM CDBC is a quad bilateral switch in- tended for the transmission or multiplexing of analog or digi- tal signals It is pin-for-pin compatible with. Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise . CD Datasheet, CD Quad Bilateral Switch Datasheet, buy CD

Author: Vogal Vogore
Country: Somalia
Language: English (Spanish)
Genre: Video
Published (Last): 28 November 2006
Pages: 209
PDF File Size: 11.32 Mb
ePub File Size: 15.47 Mb
ISBN: 519-2-13700-112-7
Downloads: 42678
Price: Free* [*Free Regsitration Required]
Uploader: Tojamuro

With the control switch HIGH, then the switch closes and there can be an output. The is a pin chip. If the pushbuttons are not pressed down, then no signal will appear at the outputs. Without the control or enable switch, there can be no output.

The switches are labeled from 1 to 4. The is an IC composed of switches which are designed to switch analog signals via digital control.

Each switch has an input, output, and control terminal. V DD and ground, pins 14 and 7, are the power pins. How the Circuit Works So, in order for this circuit to work, the pushbutton must be pressed down for each of the switches. In this circuit, we will show the basic functionality of the chip by passing analog signals through 2 of the switches by digital control. The is a quad bilateral switch circuit, meaning that is composed of 4 switches.

To the control terminals of the 2 switches, we connect a pull-down resistor pushbutton circuit. The pinout of the chip is shown below.

  BEHRINGER FEEDBACK DESTROYER PRO FBQ2496 PDF

One place it can be obtained is at Taydaelectronics at the following link: A bilateral switch acts as a single pole, single throw switch. So current can flow in one direction and the other direction, depending on which side is dtasheet input.

How to Build a Quad Bilateral Switch Circuit

You can view the control terminal as the signal which closes the switch so that the input signal can cross over to the output. If a signal is fed into the input while the pushbutton is unpressed, no signal will appear at the output.

The has a wide operating voltage of 5VV. This enables the signal at the input to go to the output. Each switch has a single input and a dahasheet output terminal.

When unpressed, the pushbutton has the signal LOW by default. The quad bilateral switch chip is a chip that is made up of 4 switches. For datxsheet circuit, we are only going to be using 2 of the 4 switches. The most common waveform is a sine wave. As the quad term implies, the is composed up of 4 switches. When pressed down, the pushbutton makes the signal HIGH. Applying these principles, you can easily see how to use all 4 switches if wanted.

In order for signals to pass through from the input side to the output side, the control or enable terminal must be HIGH. So you will see that if you press datsaheet the pushbutton with an analog signal or digital signal at the input, that same signal will appear at hte output.

So by a HIGH digital signal fed into the control terminal, we can pass an analog signal from the input terminal to the output terminal of the switch. This means that either side of the switch can be used as the input.

  CMW RUTENBAU PDF

How to Build a 4066 Quad Bilateral Switch Circuit

How to Build a Quad Bilateral Switch Circuit In this circuit, we will show dataeheet to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip. The really functions as an analog switch.

Each switch also has a control or enable terminal. What this means is we feed an analog signal into the input of the switch and it reaches the output only if a HIGH digital signal is fed into the control or enable terminal. This establishes sufficient power to the chip. To the inputs of the 2 switches, we feed an analog signal. In this circuit, we will show how to connect a bilateral switch chip to inputs and outputs using the quad bilateral switch chip.

CD Datasheet(PDF) – TI store

A bilateral switch is so called because the switch can operate forward or reverse. First, to power thewe connect 5V of power to V DDpin 14, and we connect the ground datashee, pin 7, to ground. The control terminal enables the input to go to output. The datasheet for the can be found at the following link: It can be obtained cheaply at a number of online electronic retailers.